Construction of the Hill48 and Yld89 for Auto-body Steel Sheets considering the Strain Rate

This paper deals with the anisotropic material properties and the initial yield locus considering the strain rate. Uni-axial tensile tests are performed with variation of the strain rate in order to obtain flow stress curves and the tensile properties. The R-values have been measured with a high speed camera by analyzing the deformation history during the tensile test. Anisotropy of auto-body steel sheets have been described by using Hill48 and Yld89 (Barlat89) yield functions according to the strain rate ranged from 0.001/sec to 100/sec. Hill48 and Yld89 yield loci of auto-body steel sheets at various strain rates have been constructed in order to visualize the initial yield state. The performance of two yield criteria is evaluated by comparing yield loci constructed in the principal stress plane. The initial yield locus becomes different from the static one when the strain rate is considered to describe the anisotropy of the steel sheets

Electronic density of states derived from thermodynamic critical field curves for underdoped La-Sr-Cu-O

Thermodynamic critical field curves have been measured for $La_{2-x}Sr_{x}CuO_{4+\delta}$ over the full range of carrier concentrations where superconductivity occurs in order to determine changes in the normal state density of states with carrier concentration. There is a substantial window in the $H-T$ plane where the measurements are possible because the samples are both thermodynamically reversible and the temperature is low enough that vortex fluctuations are not important. In this window, the data fit Hao-Clem rather well, so this model is used to determine $H_c$ and $\kappa_c$ for each temperature and carrier concentration. Using N(0) and the ratio of the energy gap to transition temperature, $\Delta (0)/k_BT_c$, as fitting parameters, the $H_c vs T$ curves give $\Delta (0)/k_BT_c \sim 2.0$ over the whole range of $x$. Values of N(0) remain rather constant in the optimum-doped and overdoped regime, but drops quickly toward zero in the underdoped regime.

Effects of 3D-printed polycaprolactone/��-tricalcium phosphate membranes on guided bone regeneration

This study was conducted to compare 3D-printed polycaprolactone (PCL) and polycaprolactone/��-tricalcium phosphate (PCL/��-TCP) membranes with a conventional commercial collagen membrane in terms of their abilities to facilitate guided bone regeneration (GBR). Fabricated membranes were tested for dry and wet mechanical properties. Fibroblasts and preosteoblasts were seeded into the membranes and rates and patterns of proliferation were analyzed using a kit-8 assay and by scanning electron microscopy. Osteogenic differentiation was verified by alizarin red S and alkaline phosphatase (ALP) staining. An in vivo experiment was performed using an alveolar bone defect beagle model, in which defects in three dogs were covered with different membranes. CT and histological analyses at eight weeks after surgery revealed that 3D-printed PCL/��-TCP membranes were more effective than 3D-printed PCL, and substantially better than conventional collagen membranes in terms of biocompatibility and bone regeneration and, thus, at facilitating GBR. ? 2017 by the authors. Licensee MDPI, Basel, Switzerland.118Ysciescopu

Three-dimensional pattern formation, multiple homogeneous soft modes, and nonlinear dielectric electroconvection

Patterns forming spontaneously in extended, three-dimensional, dissipative systems are likely to excite several homogeneous soft modes ($\approx$ hydrodynamic modes) of the underlying physical system, much more than quasi one- and two-dimensional patterns are. The reason is the lack of damping boundaries. This paper compares two analytic techniques to derive the patten dynamics from hydrodynamics, which are usually equivalent but lead to different results when applied to multiple homogeneous soft modes. Dielectric electroconvection in nematic liquid crystals is introduced as a model for three-dimensional pattern formation. The 3D pattern dynamics including soft modes are derived. For slabs of large but finite thickness the description is reduced further to a two-dimensional one. It is argued that the range of validity of 2D descriptions is limited to a very small region above threshold. The transition from 2D to 3D pattern dynamics is discussed. Experimentally testable predictions for the stable range of ideal patterns and the electric Nusselt numbers are made. For most results analytic approximations in terms of material parameters are given.Comment: 29 pages, 2 figure

Likelihood Geometry

We study the critical points of monomial functions over an algebraic subset of the probability simplex. The number of critical points on the Zariski closure is a topological invariant of that embedded projective variety, known as its maximum likelihood degree. We present an introduction to this theory and its statistical motivations. Many favorite objects from combinatorial algebraic geometry are featured: toric varieties, A-discriminants, hyperplane arrangements, Grassmannians, and determinantal varieties. Several new results are included, especially on the likelihood correspondence and its bidegree. These notes were written for the second author's lectures at the CIME-CIRM summer course on Combinatorial Algebraic Geometry at Levico Terme in June 2013.Comment: 45 pages; minor changes and addition

Snap evaporation of droplets on smooth topographies

Droplet evaporation on solid surfaces is important in many applications including printing, micro-patterning and cooling. While seemingly simple, the configuration of evaporating droplets on solids is difficult to predict and control. This is because evaporation typically proceeds as a “stick-slip” sequence—a combination of pinning and de-pinning events dominated by static friction or “pinning”, caused by microscopic surface roughness. Here we show how smooth, pinning-free, solid surfaces of non-planar topography promote a different process called snap evaporation. During snap evaporation a droplet follows a reproducible sequence of configurations, consisting of a quasi-static phase-change controlled by mass diffusion interrupted by out-of-equilibrium snaps. Snaps are triggered by bifurcations of the equilibrium droplet shape mediated by the underlying non-planar solid. Because the evolution of droplets during snap evaporation is controlled by a smooth topography, and not by surface roughness, our ideas can inspire programmable surfaces that manage liquids in heat- and mass-transfer applications

Impact of RF mismatches on the performance of massive MIMO systems with ZF precoding

Thanks to the channel reciprocity, the time division duplex (TDD) operation is more preferred in massive multiple-input multiple-output (MIMO) systems. Avoiding the heavy feedback of downlink channel state information (CSI) from the user equipment (UE) to the base station (BS), the uplink CSI can be exploited for the downlink precoding. However, due to the mismatches of the radio frequency (RF) circuits at both sides of the link, the whole communication channels are usually not symmetric in practical systems. This paper is focused on the RF mismatches at the UEs and the BS for the multi-user massive MIMO systems with zero forcing (ZF) precoding. The closed-form expressions of the ergodic sum-rates are derived for evaluating the impact of RF mismatches on the system performance. Theoretical analysis and simulation results show that the RF mismatches at the UEs only lead to a negligible performance loss. However, it is imperative to perform reciprocity calibration at the BS, because the RF mismatches at the BS contribute to the inter-user interference (IUI) and result in a severe system performance degradation

Application of emulsified acids on sandstone formation at elevated temperature conditions: an experimental study

Emulsified acid has attracted considerable attention of the oil and gas industry due to its delayed nature that allows deeper penetration of acid into the formation which essentially facilitate further enhancing the well productivity, and at the same time minimizes the corrosion issues. However, emulsified acid has only been extensively studied and applied on carbonate formations. Considering more than half of the reservoirs worldwide are sandstone reservoirs, studying the effects of emulsified acid on sandstone under high-temperature conditions would unlock the potential of emulsified acid and help generate more value for the oil and gas industry by improving the well productivity from sandstone reservoirs. To ensure the applicability of the emulsified acid on the real sandstone reservoir, which usually has a temperature higher than ambient conditions, the stability of emulsified acids is investigated under 300 °F. Then, the stable emulsified acid samples are developed and their impact on the properties of Berea sandstone core samples, including porosity, pore-size distribution, permeability and wettability, are investigated. The core samples have undergone pre-flush (10% HCl:5% CH3COOH) before the main flush (emulsified acid). The emulsified acids are prepared using hydrofluoric acid, hydrochloric acid, phosphoric acid, cationic surfactant and chelating agent. Fourteen core samples are saturated with different emulsified acids under vacuum conditions for 3 days to ensure maximum saturation. The porosity, permeability and wettability of each core sample are measured before and after the reaction with acid. Nuclear magnetic resonance analysis has been applied to evaluate the change in pore size distribution. This study has demonstrated that the emulsified acids are capable of improving the porosity and permeability of Berea sandstone core sample. The pore size distribution has also been affected by the application of emulsified acid, where more large pores have been evolved to the core samples due to the reaction of acids with the sandstone which ultimately helps in improving the productivity of hydrocarbons. This indicates less precipitation of the secondary reaction products resulting better enhancement in sandstone flow properties. These results demonstrate the potential of emulsified acid during sandstone acidizing as emulsified acid significantly improved the sandstone properties which can essentially enhance the well productivity

Bidirectional Interactions between Antigen-bearing Respiratory Tract Dendritic Cells (DCs) and T Cells Precede the Late Phase Reaction in Experimental Asthma: DC Activation Occurs in the Airway Mucosa but Not in the Lung Parenchyma

The airway mucosal response to allergen in asthma involves influx of activated T helper type 2 cells and eosinophils, transient airflow obstruction, and airways hyperresponsiveness (AHR). The mechanism(s) underlying transient T cell activation during this inflammatory response is unclear. We present evidence that this response is regulated via bidirectional interactions between airway mucosal dendritic cells (AMDC) and T memory cells. After aerosol challenge, resident AMDC acquire antigen and rapidly mature into potent antigen-presenting cells (APCs) after cognate interactions with T memory cells. This process is restricted to dendritic cells (DCs) in the mucosae of the conducting airways, and is not seen in peripheral lung. Within 24 h, antigen-bearing mature DCs disappear from the airway wall, leaving in their wake activated interleukin 2R+ T cells and AHR. Antigen-bearing activated DCs appear in regional lymph nodes at 24 h, suggesting onward migration from the airway. Transient up-regulation of CD86 on AMDC accompanies this process, which can be reproduced by coculture of resting AMDC with T memory cells plus antigen. The APC activity of AMDC can be partially inhibited by anti-CD86, suggesting that CD86 may play an active role in this process and/or is a surrogate for other relevant costimulators. These findings provide a plausible model for local T cell activation at the lesional site in asthma, and for the transient nature of this inflammatory response

EVOG: a database for evolutionary analysis of overlapping genes

Overlapping genes are defined as a pair of genes whose transcripts are overlapped. Recently, many cases of overlapped genes have been investigated in various eukaryotic organisms; however, their origin and transcriptional control mechanism has not yet been clearly determined. In this study, we implemented evolutionary visualizer for overlapping genes (EVOG), a Web-based DB with a novel visualization interface, to investigate the evolutionary relationship between overlapping genes. Using this technique, we collected and analyzed all overlapping genes in human, chimpanzee, orangutan, marmoset, rhesus, cow, dog, mouse, rat, chicken, Xenopus, zebrafish and Drosophila. This integrated database provides a manually curated database that displays the evolutionary features of overlapping genes. The EVOG DB components included a number of overlapping genes (10‱074 in human, 10 ‱009 in chimpanzee, 67 ‱039 in orangutan, 51 001 in marmoset, 219 in rhesus, 3627 in cow, 209 in dog, 10 ‱700 in mouse, 7987 in rat, 1439 in chicken, 597 in Xenopus, 2457 in zebrafish and 4115 in Drosophila). The EVOG database is very effective and easy to use for the analysis of the evolutionary process of overlapping genes when comparing different species. Therefore, EVOG could potentially be used as the main tool to investigate the evolution of the human genome in relation to disease by comparing the expression profiles of overlapping genes. EVOG is available at http://neobio.cs.pusan.ac.kr/evog/